Nbr 90 O Ring

Send Inquiry
Nbr 90 O Ring
Details
NBR 90 O Rings for oil-side sealing positions where higher hardness is required to support pressure-loaded static grooves.
90 Shore A NBR: Quoted for oil-side grooves where softer nitrile may extrude under pressure.
Oil Contact: For mineral hydraulic oil, grease, air, and selected fuel-related service after fluid review.
Static Groove Focus: Best discussed for valve blocks, pump housings, threaded plugs, filter housings, and pressure fittings.
Not for Weather Use: Ozone, sunlight, steam, brake fluid, and aromatic solvents need another compound review.
Factory MOQ: Usually from 1,000 pcs per size; custom sizes are quoted after drawing check.
Category
O Ring
Share to
Description

Technical Specifications

 

 

Item

Factory Specification

Product Name

nbr 90 o ring

Material

NBR / Nitrile Rubber / Buna-N

Hardness

90 Shore A

Hardness Tolerance

Commonly ±5 Shore A, unless specified by drawing

Size Standard

AS568, ISO 3601, metric, inch, custom sizes

Dimension Basis

ID, CS, OD; OD = ID + 2 × CS

Temperature Range

Typical -30°C to +100°C; higher service depends on compound and condition

Main Media

Mineral hydraulic oil, grease, air, selected diesel or fuel oil after confirmation

Poor Compatibility

Ozone, weathering, strong acids, ketones, brake fluid, aromatic solvents, long outdoor exposure

Production Method

Compression molding or injection molding

MOQ

Usually from 1,000 pcs per size for standard molds; custom sizes quoted by drawing

 

colored rubber o ring materials
rubber o rings in labeled bags

 

Product Overview

 

 

A nbr 90 o ring is not a general soft sealing ring. It is usually ordered when the buyer needs a harder nitrile seal for oil-side static grooves. In pressure fittings or valve blocks, softer NBR can move toward the clearance gap after pressure cycling. The 90 Shore A grade gives stronger support, but the groove still has to provide correct squeeze.

 

VANSER produces this oil resistant rubber O ring for mineral oil, grease, hydraulic oil, air, and selected fuel-related service after fluid review. If the part must stretch heavily during assembly or work at low temperature with movement, 70 Shore A NBR may be easier to install.

 

automotive component rubber seals
hydraulic pneumatic sealing rings

 

When 90 Shore A Makes Sense

 

 

This hardness grade is mainly quoted for grooves with pressure load, tight clearance, and fixed sealing faces. It is not a better choice simply because it is harder. If the groove is shallow, the seal can be over-compressed. If the squeeze is too low, the ring may not hold pressure after cycling.

 

For moving rods, pistons, or shafts, VANSER checks lubrication, surface finish, speed, and extrusion gap before confirming 90 Shore A NBR. For outdoor equipment, steam service, ozone exposure, or brake fluid, NBR should not be approved without compound review.

 

rubber o ring production workshop

 

Fuel and Oil Confirmation

 

 

Fuel-related orders need extra care. Diesel, fuel oil, gasoline blends, biofuel content, additives, and working temperature can change rubber behavior. VANSER will not approve the compound only by old size or color. The buyer should provide fluid name, temperature, pressure, and old seal condition before bulk production.

 

For high-pressure hydraulic work, a backup ring may be needed when the extrusion gap is too large for rubber alone. Hardness helps with support, but it cannot replace correct groove design.

 

IATF 16949 certified rubber products factory

 

Application and Inspection

 

 

Before packing, VANSER checks hardness, ID, cross section, surface marks, flash, and batch quantity. Send the size, quantity, medium, pressure, temperature, application type, and hardness requirement. We will confirm tooling, MOQ, material grade, and production method before quoting.

 

O-ring material
O-ring quality inspection
O-ring Factory Collection
O-ring Factory Collection
O-ring Factory Collection
O-ring Factory Collection

Hot Tags: nbr 90 o ring, China nbr 90 o ring manufacturers, suppliers, factory

Send Inquiry